Availability: | |
---|---|
Quantity: | |
PDF Export | |
491-4
SENTAI
491-4
Require tools
A ruler, pencil, speed ruler, utility knife or lever cutter,
rubber floor hammer, if necessary, punch saw, gasket wedge and
a clapper block.
Subfloor Prep / C onditions (DIN 18365 paragraph 3)
The bottom layer must be free of old textile coverings, clean,
permanently dry, uniform, firm and stable.
Loose, soft or elastic old coverings must be removed. The flatness must conform to line 4 of table 3 of DIN 18202 and shall not exceed 2mm/ m. Any bumps must be removed and the pits filled in.The following maximum moisture content is applicable to new buildings or floor slabs:For floor heating, the maximum allowable heat output is 55W /m and must be evenly distributed throughout the area.The surface temperature of the slab shall not exceed 29℃ during heating.Installatio
Install the first board with the spring facing the wall. Then, wrap the second piece of wood from the front to the first piece.
The final element of the series will be shortened: cut the decorative side with a utility knife, then bend and break the board.Make sure that the first track is perfectly laid straight and that a distance of 10 mm with the wall wedge is ensured while ensuring that the same allowance is applied to both ends / sides.Following lines:18 19 Offsets between two adjacent lines at both ends must be at least 40cm or 1/2 board length. If the rest doesn't fit, simply start it at the beginning of the next line and use the matching New Cut.Insert the starting section into the long side of the row already in place, gently lock it up and fold. The next element also permeates the long side first and is properly locked when the head ends are folded.
installation direction }In order to ensure reliable interlocking of profiles, the longitudinal joints must be properly tapped with flapping blocks and rubber hammers.The elements in the last row were cut to the right size and a 10mm gap was installed with the wall.All wedges should be removed and baseboards or baseboards, transition rails and piping installed roselike.Cleaning and care Cleaning and caring for SPC flooring is minimal, but critical to the life of your flooring.Unsuitable detergents, sand, acidic or alkaline substances, solvents, stilettos, metal and metal wear can all attack surfaces and cause scrapes, scratches or discoloration. Furniture must have clean sliders; Office chairs must have suitable soft casters. A suitable floor mat must also be placed under the office chair. Speckles and corrosive substances must be removed from the surface immediately. The use of clean areas greatly reduces the amount of dust introduced. Clean or vacuum regularly with the nozzles of parquet floors to remove dust and loose dirt.
SPC floor stands for stone plastic composite.
The main component is lime stone (calcium carbonate),
virgin pvc powder, stabilizer and other necessary chemicals.
LIVE HEALTHY
AND COMFORTABLE
Sentai Floor products don’t contain harmful materials
and they’re absolute ECO-FRIENDLY. We can ensure
healthier and warmer flooring for everyone who chooses
our products with Sentai floor special characteristics.
ANTIMICROBIAL
PROTECTION
WATER RESISTANT
HEAT RESISTANT
EASY TO CLEAN
AND MAINTAIN
With the special Rigid Core technology, Sentai Floor can reach
waterproof, antibacterial and moisture resistant. We can
ensure you the comfortable living environment.
RIGID EASY TO CUT FLOOR OR WALL
Sentai started to produce LVT+WPC indoor flooring from 2014, and SPC flooring from 2016.
1. the production is mature after 5 year development;
2. The product quality is stable after we had improve our formula more than 30 times and products sold to more than 30 countries in the world and no big claim;
3. The production scale is among the top 10 suppliers of SPC product in China.
4. The price is very competitive because we
Require tools
A ruler, pencil, speed ruler, utility knife or lever cutter,
rubber floor hammer, if necessary, punch saw, gasket wedge and
a clapper block.
Subfloor Prep / C onditions (DIN 18365 paragraph 3)
The bottom layer must be free of old textile coverings, clean,
permanently dry, uniform, firm and stable.
Loose, soft or elastic old coverings must be removed. The flatness must conform to line 4 of table 3 of DIN 18202 and shall not exceed 2mm/ m. Any bumps must be removed and the pits filled in.The following maximum moisture content is applicable to new buildings or floor slabs:For floor heating, the maximum allowable heat output is 55W /m and must be evenly distributed throughout the area.The surface temperature of the slab shall not exceed 29℃ during heating.Installatio
Install the first board with the spring facing the wall. Then, wrap the second piece of wood from the front to the first piece.
The final element of the series will be shortened: cut the decorative side with a utility knife, then bend and break the board.Make sure that the first track is perfectly laid straight and that a distance of 10 mm with the wall wedge is ensured while ensuring that the same allowance is applied to both ends / sides.Following lines:18 19 Offsets between two adjacent lines at both ends must be at least 40cm or 1/2 board length. If the rest doesn't fit, simply start it at the beginning of the next line and use the matching New Cut.Insert the starting section into the long side of the row already in place, gently lock it up and fold. The next element also permeates the long side first and is properly locked when the head ends are folded.
installation direction }In order to ensure reliable interlocking of profiles, the longitudinal joints must be properly tapped with flapping blocks and rubber hammers.The elements in the last row were cut to the right size and a 10mm gap was installed with the wall.All wedges should be removed and baseboards or baseboards, transition rails and piping installed roselike.Cleaning and care Cleaning and caring for SPC flooring is minimal, but critical to the life of your flooring.Unsuitable detergents, sand, acidic or alkaline substances, solvents, stilettos, metal and metal wear can all attack surfaces and cause scrapes, scratches or discoloration. Furniture must have clean sliders; Office chairs must have suitable soft casters. A suitable floor mat must also be placed under the office chair. Speckles and corrosive substances must be removed from the surface immediately. The use of clean areas greatly reduces the amount of dust introduced. Clean or vacuum regularly with the nozzles of parquet floors to remove dust and loose dirt.
SPC floor stands for stone plastic composite.
The main component is lime stone (calcium carbonate),
virgin pvc powder, stabilizer and other necessary chemicals.
LIVE HEALTHY
AND COMFORTABLE
Sentai Floor products don’t contain harmful materials
and they’re absolute ECO-FRIENDLY. We can ensure
healthier and warmer flooring for everyone who chooses
our products with Sentai floor special characteristics.
ANTIMICROBIAL
PROTECTION
WATER RESISTANT
HEAT RESISTANT
EASY TO CLEAN
AND MAINTAIN
With the special Rigid Core technology, Sentai Floor can reach
waterproof, antibacterial and moisture resistant. We can
ensure you the comfortable living environment.
RIGID EASY TO CUT FLOOR OR WALL
Sentai started to produce LVT+WPC indoor flooring from 2014, and SPC flooring from 2016.
1. the production is mature after 5 year development;
2. The product quality is stable after we had improve our formula more than 30 times and products sold to more than 30 countries in the world and no big claim;
3. The production scale is among the top 10 suppliers of SPC product in China.
4. The price is very competitive because we
Contact person:Simon ren
E-mail:simon@sentaigroup.com
Mobile phone / WhatsApp:+86 17730471120
Tel:0086-0563-6988013
Address:NO 23 North jianshe Road,Guangde County ,Anhui Province ,China 242200
If you want, we'll keep you updated on the latest news about products and events
Copyright © 2021 sentaifloor Co., Ltd. Support by Leadong.