sentai spc new design wood plastic composite engineered wood spc flooring vinyl plank flooring laminate waterproof 3836-2

Require tools

A ruler, pencil, speed ruler, utility knife or lever cutter,

rubber floor hammer, if necessary, punch saw, gasket wedge and

a clapper block.

Subfloor Prep / C onditions (DIN 18365 paragraph 3)

The bottom layer must be free of old textile coverings, clean,

permanently dry, uniform, firm and stable.

Loose, soft or elastic old coverings must be removed. The flatness must conform to line 4 of table 3 of DIN 18202 and shall not exceed 2mm/ m. Any bumps must be removed and the pits filled in.The following maximum moisture content is applicable to new buildings or floor slabs:For floor heating, the maximum allowable heat output is 55W /m and must be evenly distributed throughout the area.The surface temperature of the slab shall not exceed 29℃ during heating.Installatio

Install the first board with the spring facing the wall. Then, wrap the second piece of wood from the front to the first piece.

The final element of the series will be shortened: cut the decorative side with a utility knife, then bend and break the board.Make sure that the first track is perfectly laid straight and that a distance of 10 mm with the wall wedge is ensured while ensuring that the same allowance is applied to both ends / sides.Following lines:18  19 Offsets between two adjacent lines at both ends must be at least 40cm or 1/2 board length. If the rest doesn't fit, simply start it at the beginning of the next line and use the matching New Cut.Insert the starting section into the long side of the row already in place, gently lock it up and fold. The next element also permeates the long side first and is properly locked when the head ends are folded.

installation direction }In order to ensure reliable interlocking of profiles, the longitudinal joints must be properly tapped with flapping blocks and rubber hammers.The elements in the last row were cut to the right size and a 10mm gap was installed with the wall.All wedges should be removed and baseboards or baseboards, transition rails and piping installed roselike.Cleaning and care Cleaning and caring for SPC flooring is minimal, but critical to the life of your flooring.Unsuitable detergents, sand, acidic or alkaline substances, solvents, stilettos, metal and metal wear can all attack surfaces and cause scrapes, scratches or discoloration. Furniture must have clean sliders; Office chairs must have suitable soft casters. A suitable floor mat must also be placed under the office chair. Speckles and corrosive substances must be removed from the surface immediately. The use of clean areas greatly reduces the amount of dust introduced. Clean or vacuum regularly with the nozzles of parquet floors to remove dust and loose dirt.

SPC floor stands for stone plastic composite.

The main component is lime stone (calcium carbonate),

virgin pvc powder, stabilizer and other necessary chemicals.

LIVE HEALTHY

AND COMFORTABLE

Sentai Floor products don’t contain harmful materials

and they’re absolute ECO-FRIENDLY. We can ensure

healthier and warmer flooring for everyone who chooses

our products with Sentai floor special characteristics.

ANTIMICROBIAL

PROTECTION

WATER RESISTANT

HEAT RESISTANT

EASY TO CLEAN

AND MAINTAIN

With the special Rigid Core technology, Sentai Floor can reach

waterproof, antibacterial and moisture resistant. We can

ensure you the comfortable living environment.

RIGID EASY TO CUT FLOOR OR WALL

Sentai started to produce LVT+WPC indoor flooring from 2014, and SPC flooring from 2016.

1. the production is mature after  5 year development;

2. The product quality is stable after we  had improve our formula more than 30 times and products sold  to more than 30 countries in the world and no big claim;

3.  The production scale is among the top 10 suppliers of SPC product in China.

4. The price is very competitive because we

might be the only producer who had workshop roofs been covered by solar pad of 95,000 sqm , each year generate 12,000,000 kwh electricity,around $1,700,000 every year,this give us at least 10% saving in the production cost and we willshare the benefit with customers.

4. The new product range we have is the most innovative and unique in whole industry.

6. The complete range of products are eco-friendly , certified, and recyclable.

SPC CLICK FLOOR PLANK  SPC DRY BACK  WOOD SPC FLOOR  

HERRINGBONE   DIGITAL PRINTING FLOOR

Excellent Dimensional Stability,extremly low expansion and Contraction Superb impact and indentation resistant Highly Stable to Heat, Sunlight and Water Eco-friendly, 100% Recyclable Large area installation,max. 400sqm No telegraphing Acclimation no need any more Fast-install drop down click with higher locking strength

Acoustic insulation underlayer available Have good residual indentation performance Better impact resistance Using the extruding craft , without plasticizer Eco-friendly, 100% Recyclable Using the vergin materials Real Wood Veneer, Nature & Temperature Feeling Anti-bacterial surface & Core – protecting against >99% of  harmful bacteria & fungus 100% waterproof Core 100% mould proof Core Pet proof - easy to clean when accidents happen FREE OF FORMALDEHYDE and any other harmful substances

Fool Proof Installation Virtually maintenance-free wipe clean surface W-BIO flooring is developing. W-BIO: Wood veneer +Biomass

core(Non-pvc core). Installation more beautiful W-SPC/W-BIO 100% waterproof Core W-SPC/W-BIO 100% mould proof

Core

W-SPC/W-BIO anti-bacterial surface & Core – protecting

against >99% of harmful bacteria & fungus

W-SPC/W-BIO real Wood Veneer, Nature & Temperature Feeling

The future of flooring development—Highly specilized

Super anti-scratch & wear resistance

Non- repeat No MOQ request High resolution

Extrusion UV coating  Cutting Grooving Grooving Backlayer

laying  Packing 11 Extrusion lines, 2 UV coating lines, 2 cutting lines , 3 grooving lines, 3 baclayerlaying lines, 300+

workers . Max. production capability :170-200 containers / month .Sentai R&D center build according to CNAS requirements, it have the cutting-edge facilities and an powerful innovation team. Sentai R&D center can accomplish 50+ testings , we have Artifical Weathering Test Chamber, Large and medium - sized Thermostatic Water Tank, UniversalTesting Machine Ultra-low Temperature Freezer, Constant Temperature and Humidity Sentai R&D center build according to CNAS requirements, it have the cutting-edge facilities and an powerful innovation team. Sentai R&D center can accomplish 50+ testings , we have Artifical Weathering Test Chamber, Large and medium - sized Thermostatic Water Tank, UniversalTesting Machine Ultra-low Temperature Freezer, Constant Temperature and Humidity Chamber, Taber five Finger anti-scratch test machine, Fire Retardant test machine, Aging performance testing instrument,

and etc.

THE TESTING FOR INDOOR FLOORING:

1.Castor Chair Test

2. Dimensional Stability & Curling

3.  3.Colour Fastness to

Artificial Light

4.Water absorption 5.Static load

6.Cleanability-Stain Resistance 7.Abrasion Resistance

36 Innovation patents ;

16 Innovation patents applying ; 82

Utility model patents ; 6 Design patents.

FOR COMPOSITE Moisture tester Whiteness meter Bulk density Sediment Volume Laser particle analyzer  Calcium powder PH value Constant temperature drying oven Temperature and

humidity chamber Freezing experiment box  Taber type abrasion tester Martindale abration tester Residual Imprint tester Water bath kettle  Heating test for installed floor  Fire retardancy test  Wear-resistant tester  Coater chair tester  Universal tester  Impact resistance tester  SENTAI LAB

OVERVIEW

Four production bases of Sentai Group. Anhui Sentai WPC-TEC flooring Co.,Ltd was established in 2014

and located in Guangde, Anhui province, China. It is the subsidiary of Anhui Sentai Group Co.,Ltd. Sentai WPC mainly produce SPC flooring&wall panel, wood bio flooring and digital printing flooring&wall panel. The registered capital is 48

millions RMB.  

Anhui Sentai Group Co.,Ltd covers an area of 300,000 square meters with more than 700 employees. Most of our workshop roofs have been covered by solar panels which can convey the electric energy to State Grid to lower the electricity costs of the enterprises.